Sanyo Vcc-4344 User's Manual
COLOR CCD camera
About this manual
Before installing and using the camera, please read this manual
carefully. Be sure to keep it handy for later reference.
This installation should be made by a qualified service person and should
conform to all local codes.
Depending on the conditions of use, installation and
environment, please be sure to make the appropriate settings
and adjustments. If you need help with installation and/or
settings, please consult your dealer.
INFORMATION TO USER
THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT
OPERATING AND MAINTENANCE INSTRUCTIONS IN THE
LITERATURE ACCOMPANYING THIS UNIT.
TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
For the customers in Canada
This Class B digital apparatus complies with Canadian ICES-003.
Pour la clientèle canadienne
Cet appareil numerique de la Classe B est conforme a la norme NMB-003
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential instal ation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Changes or modifications not expressly approved by Sanyo may void the user's
authority to operate this camera.
In case of problem
Do not use the camera if smoke or strange odors come from the
unit, or if it seems not to function correctly. Disconnect the power
cord immediately, and consult your dealer or a Sanyo Authorized
Do not open or modify
Do not open the cabinet, as it may be dangerous and cause
damage to the unit. For internal settings and repairs, consult your
dealer or a Sanyo Authorized Service Center.
Do not put objects inside the unit
Make sure that no metal objects or flammable substances get
inside the camera. If used with a foreign object inside, it could
cause fire, short-circuits or damage. If water or liquid gets inside the
camera, disconnect the power cord immediately, and consult your
dealer or a Sanyo Authorized Service Center. Be careful to protect
the camera from rain, sea water, etc.
Be careful when handling the unit
To prevent damage, do not drop the camera or subject it to strong
shock or vibration.
Install away from electric or magnetic fields
If installed close to a TV, radio transmitter, magnet, electric motor,
transformer, or audio speakers, the magnetic field they generate
will distort the image.
Protect from humidity and dust
To prevent damage to the camera, do not install it where there is
greasy smoke or steam, where the humidity may get too high, or
where there is a lot of dust.
Protect from high temperatures
Do not install close to stoves, or other heat generating devices,
such as spotlights, etc., or where it could be subject to direct
sunlight, as that could cause deformation, discoloration or other
Be careful when installing close to the ceiling, in a kitchen or boiler
room, as the temperature may raise to high levels. Install where the
temperature range will stay between -10
°C (14°F) and 50°C
°F). (no condensation)
Dirt can be removed from the cabinet by wiping it with a soft cloth.
To remove stains, use a soft cloth moistened with a soft detergent
solution and wrung dry, then dry by wiping with a soft dry cloth.
Do not use benzine, thinner or other chemical products on the
cabinet, as they may cause deformation and paint peeling. Before
using a chemical cloth, make sure to read all accompanying
instructions. Make sure that no plastic or rubber material comes
in contact with the cabinet for extended periods, as that may
cause damage or paint peeling.
Printed on recycled paper
SANYO Electric Co., Ltd.
Printed in Japan
POWER (power indicator)
Lights when the camera power is ON.
VIDEO OUT (video output terminal: BNC connector)
Connects to the VIDEO IN (video input) terminal on the VCR or monitor.
CONTROL (Manual color/black and white setting terminal)
G (ground) terminal
C (color) terminal
B (black and white) terminal
LINE PHASE (Line phase adjustment volume)
When using two cameras or more, the image on the monitor may roll
vertically when switching sources. This rolling can be minimized by turning
GND, AC24V, DC12V (ground terminal, 24V AC or 12V DC input
Camera adjustment/setting panel
Contains camera adjustment dials and setting switches.
LENS (lens iris output terminal)
Used to connect the lens plug when the lens is attached.
c Brake coil (-)
d Brake coil (+)
e Drive coil (+)
f Drive coil (-)
Flange-back adjustment lever
Flange-back lock screw
Protects the lens from damage.
Camera installation bracket
The bracket can be secured at the top or bottom of the camera. When
securing the bracket, use the long screws and use the short screws on the
opposite side to seal the openings.
c Short screws: M3 x 4
d Long screws: M3 x 6
e Camera mounting screw hole: 1/4”-20 UNC
When installing the camera support, select a location that can support the
total weight of the camera and accessories.
Attaching the lens
Use a DC type auto-iris lens (sold separately).
Do not use a lens if length “L” is more than 5 mm.
Otherwise, it may damage the camera and prevent
When attaching a C mount lens, attach the lens to the
camera after inserting the C mount ring (option).
1 Remove the lens mount
cap from the camera.
2 Install the auto-iris lens.
3 Connect the lens plug to
the lens iris output
connector (LENS) on the
side of the camera.
NAMES AND FUNCTIONS OF PARTS
G C B
CS mount type lens
Before sending the camera out for repair, check the items below.
If the problem persists after checking these items, contact your
place of purchase or a Sanyo Authorized Service Center.
If no image appears
Is the coaxial cable attached securely?
Are the power and voltage normal?
Has the iris of the lens inside the camera been adjusted correctly
(with the iris dial)?
Is there adequate illumination?
If the image is unclear
Is the lens in focus?
Is the lens dirty?
Dirt or fingerprints on the lens can adversely affect the image.
Gently wipe any dirt or fingerprints off the lens with a soft cloth or
lens cleaning paper and cleaning fluid (commercially available).
Is the monitor adjusted correctly?
The camera is a precision instrument. Handle it carefully and
always follow the safety precautions. If the camera requires service,
never try to repair it yourself or open the casing.
For servicing, maintenance, or repairs, contact your place of
purchase or a Sanyo Authorized Service Center.
Appearance and specifications are subject to change without prior notice.
: NTSC standard TV system
(525 TV lines, 30 frames/sec.)
: PLL 2:1 interlace
: 1/4 inch solid state image device CCD
: 537 (H) x 505 (V)
: 510 (H) x 492 (V)
Synchronizing system : Internal sync, Line lock manually switchable
: 350 TV lines horizontally (color mode),
380 TV lines horizontally (B/W mode),
350 TV lines vertically
Video output level
: 1.0 Vp-p/75 ohms, composite
Video S/N ratio
: More than 48 dB
: Approx. 0.05 lux with a F 1.2 lens (B/W mode),
Approx. 0.9 lux with a F 1.2 lens (color mode),
Approx. 0.02 lux with a F 1.2 lens (B/W mode, Gain: HI)
: AUTO/MANUAL (at CONTROL terminal)
: Manual color/black and white setting
: MULTI/OFF switching
(Active when using an auto-iris lens)
: EI/AI switching
Auto-iris lens output
: DC output (variable DC level), 4-pin terminal
Electronic iris range
: 0.9 lux to 45000 lux (F 1.2 lens: color mode)
: 12.5 mm ±0.5 mm
: ATW/Manual switching
: HI (high)/ NOR (Normal) switching
: CS mount
: Temperature: -10°C – +50°C
Humidity: less than 90% (no condensation)
: 12 – 15 VDC/24 VAC, 60 Hz (±10%)
: 3.2 W (with auto iris lens)
: Approx. 430 g (without lens)
e_l5an4_us.fm Page 1 Wednesday, July 16, 2003 5:37 PM
Related Manuals for Sanyo Vcc-4344
GE Home Security System 45129 User's Manual
Bosch Home Security System Bosch Appliances Home Security System DS7400XI User's Manual
Bosch Home Security System D7412GV3 User's Manual
Bosch Home Security System ICP-CC488 User's Manual
GE Home Security System CC-SCRS01 User's Manual
GE Home Security System General Electric Home Security System FTP-1000 User's Manual
GE Home Security System General Electric Home Security System NX-116E User's Manual
GE Home Security System General Electric Home Security System NX-124E User's Manual
Honeywell Home Security System Galaxy 16 Plus User's Manual
Samsung Home Security System 720p Hdtv Camera SDC8340BU User's Manual
Samsung Home Security System 8 Channel Hdtv Hybrid Dvr SDR4200 User's Manual
Creative Home Security System WIRELESS RECEIVER SB1122 User's Manual
Radio Shack Home Security System Wireless Key-Lock Door/Window Alarm 49-118 User's Manual
La Crosse Technology Home Security System WT-5120 User's Manual
Magellan Home Security System MG-PMD75 User's Manual
Firstech, LLC. Home Security System COMPUSTAR CM3000 User's Manual
Linear Home Security System DXT-41 User's Manual
Pelco Home Security System ENDURA WS5000 User's Manual
Pelco Home Security System Pelco Home Security System CM9700-CC1 User's Manual
APC Home Security System NetBotz NBRK0570 User's Manual
Total Commander Home Security System COMMANDER 2000 User's Manual
SkyLink Home Security System HA-300 User's Manual
Enviro Home Security System EA800 User's Manual
INSTEON Home Security System 2842-222 User's Manual